calc: The Standard Interface
1.5.2 The Standard Calc Interface
---------------------------------
Calc’s standard interface acts like a traditional RPN calculator,
operated by the normal Emacs keyboard. When you type ‘C-x * c’ to start
the Calculator, the Emacs screen splits into two windows with the file
you were editing on top and Calc on the bottom.
...
--**-Emacs: myfile (Fundamental)----All----------------------
--- Emacs Calculator Mode --- |Emacs Calculator Trail
2: 17.3 | 17.3
1: -5 | 3
. | 2
| 4
| * 8
| ->-5
|
--%*-Calc: 12 Deg (Calculator)----All----- --%*- *Calc Trail*
In this figure, the mode-line for ‘myfile’ has moved up and the
“Calculator” window has appeared below it. As you can see, Calc
actually makes two windows side-by-side. The lefthand one is called the
“stack window” and the righthand one is called the “trail window.” The
stack holds the numbers involved in the calculation you are currently
performing. The trail holds a complete record of all calculations you
have done. In a desk calculator with a printer, the trail corresponds
to the paper tape that records what you do.
In this case, the trail shows that four numbers (17.3, 3, 2, and 4)
were first entered into the Calculator, then the 2 and 4 were multiplied
to get 8, then the 3 and 8 were subtracted to get -5. (The ‘>’ symbol
shows that this was the most recent calculation.) The net result is the
two numbers 17.3 and -5 sitting on the stack.
Most Calculator commands deal explicitly with the stack only, but
there is a set of commands that allow you to search back through the
trail and retrieve any previous result.
Calc commands use the digits, letters, and punctuation keys. Shifted
(i.e., upper-case) letters are different from lowercase letters. Some
letters are “prefix” keys that begin two-letter commands. For example,
‘e’ means “enter exponent” and shifted ‘E’ means ‘e^x’. With the ‘d’
(“display modes”) prefix the letter “e” takes on very different
meanings: ‘d e’ means “engineering notation” and ‘d E’ means ““eqn”
language mode.”
There is nothing stopping you from switching out of the Calc window
and back into your editing window, say by using the Emacs ‘C-x o’
(‘other-window’) command. When the cursor is inside a regular window,
Emacs acts just like normal. When the cursor is in the Calc stack or
trail windows, keys are interpreted as Calc commands.
When you quit by pressing ‘C-x * c’ a second time, the Calculator
windows go away but the actual Stack and Trail are not gone, just
hidden. When you press ‘C-x * c’ once again you will get the same stack
and trail contents you had when you last used the Calculator.
The Calculator does not remember its state between Emacs sessions.
Thus if you quit Emacs and start it again, ‘C-x * c’ will give you a
fresh stack and trail. There is a command (‘m m’) that lets you save
your favorite mode settings between sessions, though. One of the things
it saves is which user interface (standard or Keypad) you last used;
otherwise, a freshly started Emacs will always treat ‘C-x * *’ the same
as ‘C-x * c’.
The ‘q’ key is another equivalent way to turn the Calculator off.
If you type ‘C-x * b’ first and then ‘C-x * c’, you get a full-screen
version of Calc (‘full-calc’) in which the stack and trail windows are
still side-by-side but are now as tall as the whole Emacs screen. When
you press ‘q’ or ‘C-x * c’ again to quit, the file you were editing
before reappears. The ‘C-x * b’ key switches back and forth between
“big” full-screen mode and the normal partial-screen mode.
Finally, ‘C-x * o’ (‘calc-other-window’) is like ‘C-x * c’ except
that the Calc window is not selected. The buffer you were editing
before remains selected instead. If you are in a Calc window, then ‘C-x
* o’ will switch you out of it, being careful not to switch you to the
Calc Trail window. So ‘C-x * o’ is a handy way to switch out of Calc
momentarily to edit your file; you can then type ‘C-x * c’ to switch
back into Calc when you are done.
Info Catalog
calc: Starting Calc
calc: Using Calc
calc: Quick Mode Overview