binutils: Bug Reporting
18.2 How to Report Bugs
=======================
A number of companies and individuals offer support for GNU products.
If you obtained the binary utilities from a support organization, we
recommend you contact that organization first.
You can find contact information for many support companies and
individuals in the file 'etc/SERVICE' in the GNU Emacs distribution.
In any event, we also recommend that you send bug reports for the
binary utilities to <http://www.sourceware.org/bugzilla/>.
The fundamental principle of reporting bugs usefully is this: *report
all the facts*. If you are not sure whether to state a fact or leave it
out, state it!
Often people omit facts because they think they know what causes the
problem and assume that some details do not matter. Thus, you might
assume that the name of a file you use in an example does not matter.
Well, probably it does not, but one cannot be sure. Perhaps the bug is
a stray memory reference which happens to fetch from the location where
that pathname is stored in memory; perhaps, if the pathname were
different, the contents of that location would fool the utility into
doing the right thing despite the bug. Play it safe and give a
specific, complete example. That is the easiest thing for you to do,
and the most helpful.
Keep in mind that the purpose of a bug report is to enable us to fix
the bug if it is new to us. Therefore, always write your bug reports on
the assumption that the bug has not been reported previously.
Sometimes people give a few sketchy facts and ask, "Does this ring a
bell?" This cannot help us fix a bug, so it is basically useless. We
respond by asking for enough details to enable us to investigate. You
might as well expedite matters by sending them to begin with.
To enable us to fix the bug, you should include all these things:
* The version of the utility. Each utility announces it if you start
it with the '--version' argument.
Without this, we will not know whether there is any point in
looking for the bug in the current version of the binary utilities.
* Any patches you may have applied to the source, including any
patches made to the 'BFD' library.
* The type of machine you are using, and the operating system name
and version number.
* What compiler (and its version) was used to compile the
utilities--e.g. "'gcc-2.7'".
* The command arguments you gave the utility to observe the bug. To
guarantee you will not omit something important, list them all. A
copy of the Makefile (or the output from make) is sufficient.
If we were to try to guess the arguments, we would probably guess
wrong and then we might not encounter the bug.
* A complete input file, or set of input files, that will reproduce
the bug. If the utility is reading an object file or files, then
it is generally most helpful to send the actual object files.
If the source files were produced exclusively using GNU programs
(e.g., 'gcc', 'gas', and/or the GNU 'ld'), then it may be OK to
send the source files rather than the object files. In this case,
be sure to say exactly what version of 'gcc', or whatever, was used
to produce the object files. Also say how 'gcc', or whatever, was
configured.
* A description of what behavior you observe that you believe is
incorrect. For example, "It gets a fatal signal."
Of course, if the bug is that the utility gets a fatal signal, then
we will certainly notice it. But if the bug is incorrect output,
we might not notice unless it is glaringly wrong. You might as
well not give us a chance to make a mistake.
Even if the problem you experience is a fatal signal, you should
still say so explicitly. Suppose something strange is going on,
such as your copy of the utility is out of sync, or you have
encountered a bug in the C library on your system. (This has
happened!) Your copy might crash and ours would not. If you told
us to expect a crash, then when ours fails to crash, we would know
that the bug was not happening for us. If you had not told us to
expect a crash, then we would not be able to draw any conclusion
from our observations.
* If you wish to suggest changes to the source, send us context
diffs, as generated by 'diff' with the '-u', '-c', or '-p' option.
Always send diffs from the old file to the new file. If you wish
to discuss something in the 'ld' source, refer to it by context,
not by line number.
The line numbers in our development sources will not match those in
your sources. Your line numbers would convey no useful information
to us.
Here are some things that are not necessary:
* A description of the envelope of the bug.
Often people who encounter a bug spend a lot of time investigating
which changes to the input file will make the bug go away and which
changes will not affect it.
This is often time consuming and not very useful, because the way
we will find the bug is by running a single example under the
debugger with breakpoints, not by pure deduction from a series of
examples. We recommend that you save your time for something else.
Of course, if you can find a simpler example to report _instead_ of
the original one, that is a convenience for us. Errors in the
output will be easier to spot, running under the debugger will take
less time, and so on.
However, simplification is not vital; if you do not want to do
this, report the bug anyway and send us the entire test case you
used.
* A patch for the bug.
A patch for the bug does help us if it is a good one. But do not
omit the necessary information, such as the test case, on the
assumption that a patch is all we need. We might see problems with
your patch and decide to fix the problem another way, or we might
not understand it at all.
Sometimes with programs as complicated as the binary utilities it
is very hard to construct an example that will make the program
follow a certain path through the code. If you do not send us the
example, we will not be able to construct one, so we will not be
able to verify that the bug is fixed.
And if we cannot understand what bug you are trying to fix, or why
your patch should be an improvement, we will not install it. A
test case will help us to understand.
* A guess about what the bug is or what it depends on.
Such guesses are usually wrong. Even we cannot guess right about
such things without first using the debugger to find the facts.
Info Catalog
binutils: Bug Criteria
binutils: Reporting Bugs